Characteristic Values of Sanalloy Grades

For further information, please click each GRADE.

WC Grain Size CIS
Classification
Grades Specific
Gravity
Hardness Transverse
Rupture
Strength
Compressive
Strength
Fracture
Toughness
Young's
Modulus
Poisson's
Ratio
Coefficient
of Thermal
Expansion
Coefficient
of Thermal
Conductivity
Characteristic Applications
HRA HV GPa GPa MPa・m1/2 GPa MK-1 W/m・k Corrosion
Resistance
Wear
Resistance
Impact
Resistance
Seizure
Resistance
Chipping
Resistance
High-Fracture
Toughness
Hot
Forging
Non
Magnetic
Ultrafine Grain VF-10 RF06 14.9 93.5 1820 3.2 6.0 11 620 0.21 5.1 79           Nozzles,Plugs,Drawing dies,Bushes,Plungers,Various gauge blocks,Cutting blades,Slitters,Progressive dies,Press-forming dies,Powder compacting dies,Dies for molding resins and glass,Blanking punches,Punches for deep drawing,Dies for deep drawing,Bending dies
VF-30 RF10 14.6 91.5 1510 3.3 5.5 14 590 0.21 5.3 75          
VF-40 RF20 14.1 90.0 1350 3.5 5.3 16 540 0.22 5.5 71          
VF-50 RF30 13.6 88.0 1160 3.5 5.1 17 490 0.23 5.7 68          
VF-30 PRF9N 14.6 91.5 1510 3.0 5.5 13 590 0.21 5.3 75         Nozzles,Drawing dies,Bushes,Cutting blades,Slitters,Progressive dies,Press-forming dies,Powder compacting dies,Blanking punches,Dies for deep drawing,Bending dies
VF-40 PRF14N 14.1 90.0 1350 3.5 5.3 15 540 0.22 5.5 71        
VF-20 FD25 14.0 92.0 1570 3.9 5.9 11 550 0.22 5.5 71             Nozzles,Plugs,Drawing dies,Bushes,Plungers,Various gauge blocks,Cutting blades,Slitters,Progressive dies,Press-forming dies,Powder compacting dies,Dies for molding resins and glass,Blanking punches,Punches for deep drawing,Dies for deep drawing
VF-30 FD15 14.3 91.0 1450 3.3 5.4 12 560 0.22 5.3 71              
VF-40 FRT15 14.1 90.5 1400 3.3 5.2 14 550 0.22 5.5 71            
Microfine Grain VF-20 DA10 15.1 92.5 1640 3.0 5.9 11 630 0.21 4.8 79              
VF-20 KA10 14.9 92.5 1640 2.8 5.8 11 630 0.21 4.8 79             General cutting tools,Powder compacting dies
VF-30 KA20 14.8 91.5 1510 2.5 5.4 12 620 0.21 5.0 75            
NF-30 NA20 14.5 91.0 1450 3.3 4.9 12 570 0.22 5.1 71             Nozzles,Seal rings,Powder compacting dies,Corrosion-resistant molds,Nonmagnetic molds,Dies for molding resins and glass
NF-40 NA30 14.0 89.5 1250 3.6 4.7 14 540 0.23 5.4 67            
Fine Grain VM-30 RD20 14.8 91.5 1510 2.9 5.5 14 610 0.21 5.0 79             Nozzles,Plugs,Drawing dies,Bushes,Guides,Center tips,Various gauge blocks,Cutting blades,Slitters,Guide rolls,Progressive dies,Press-forming dies,Powder compacting dies,Punches,Blanking punches,Punches for deep drawing,Dies for deep drawing,Bending dies
VM-30 RD25 14.6 91.0 1450 3.3 5.3 15 590 0.21 5.1 75            
VM-40 RD30 14.4 90.0 1350 3.5 5.2 16 570 0.22 5.2 75            
VM-40 RD50 14.1 89.0 1250 3.7 4.8 17 540 0.23 5.4 71            
VM-50 RD60 13.8 88.0 1160 3.5 4.4 18 520 0.23 5.6 69            
VM-30 PRD9N 14.6 91.0 1450 3.0 5.3 15 590 0.21 5.1 75           Nozzles,Drawing dies,Bushes,Guide rolls,Progressive dies,Press-forming dies,Powder compacting dies,Punches,Blanking punches,Punches for deep drawing,Dies for deep drawing,Bending dies,End-surface reforming dies
VM-40 PRD14N 14.1 89.0 1250 3.5 4.8 17 540 0.23 5.4 71          
VM-50 PRD20N 13.5 87.0 1070 3.2 4.0 19 490 0.24 5.8 67          
Medium Grain VC-30 REA25 15.0 91.0 1450 2.6 5.1 15 620 0.21 4.8 79           Drawing dies,Bushes,Slitters,Crushing tools,Reforming rolls,Guide rolls,Press-forming dies,Powder compacting dies,Punches,Dies for deep drawing,Header dies,Former dies
VC-40 REA35 14.6 89.0 1250 3.3 4.7 17 580 0.22 5.2 75          
VC-50 REA65 14.0 87.0 1070 3.4 4.2 21 530 0.23 5.6 71          
VC-60 REA75 13.5 85.5 970 3.2 3.6 25 490 0.24 6.1 67          
VC-70 REA85 13.1 83.5 860 3.0 3.4 28 440 0.24 6.5 63          
VC-50 KEA45 14.4 88.0 1160 3.0 4.2 16 550 0.22 5.5 71           Dies for warm/hot forging,Valve molds,Crushing dies,Sizing dies
Coarse Grain VU-50 RV46 14.6 88.0 1160 3.1 4.3 21 580 0.22 5.2 75             Crushing tools,Milling rolls,Reforming rolls,Dies for hot forging,Punches,Header dies,Former dies
VU-60 RV56 14.2 86.5 1040 2.8 4.1 23 550 0.22 5.5 71            
VU-60 RV66 14.0 86.0 1000 2.8 3.9 25 530 0.23 5.6 71            
VU-70 RV76 13.6 84.5 910 2.7 3.6 27 490 0.23 6.1 67            
VU-70 RV86 13.4 83.5 860 2.7 3.4 28 460 0.24 6.3 67            
VU-70 RL89 13.5 83.0 840 2.5 3.4 30 480 0.24 6.2 67            
VU-40 RX71 14.9 90.0 1350 2.2 4.8 18 610 0.21 4.8 79           Blanking punches,Backward punches,Deformed punches,Deformed dies such as spiders and bevel gears,Various forging dies such as diff-pinion and pinion-gears
VU-50 RX92 14.5 87.5 1110 2.8 4.5 24 570 0.22 5.3 74          
VU-60 RX73 14.3 86.5 1040 2.5 4.2 25 550 0.22 5.4 73          
VU-70 RX75 13.7 84.5 910 2.4 3.8 28 500 0.24 6.0 68          
VU-70 RX94 13.1 82.5 810 2.4 3.4 32 450 0.24 6.5 63          
VU-80 RX95 12.8 81.0 770 2.2 3.2 35 410 0.25 6.6 61          
VU-40 PRV6N 14.9 90.0 1350 2.4 4.8 18 610 0.21 4.8 79         Crushing tools,Progressive dies,Deformed punches,Deformed dies
VU-60 PRV12N 14.3 86.5 1040 2.5 4.2 25 550 0.22 5.4 73        
VU-70 PRV18N 13.7 84.5 910 2.4 3.8 28 500 0.24 6.0 68        
VU-70 PRV24N 13.2 82.5 810 2.3 3.4 32 450 0.24 6.5 63        
RU-60 WM7 14.4 85.0 940 2.1 3.9 23 570 0.22 5.6 71         Hot milling rolls,Dies for warm/hot forging,Blanking punches,Crushing dies,Sizing dies
RU-70 WX80 13.7 83.0 840 2.4 3.5 26 510 0.24 6.1 66        

※The characteristic values above are not standard values,but typical values.
※The above characteristic values are subject to change without notice.

Characteristic Values Table PDF

ページトップへ